变直径旋翼直升机飞行性能研究

为了研究旋翼直径变化对直升机性能的提升作用,将旋翼动力学综合模型与机身模型相耦合,采用前飞配平方法计算稳态时旋翼操纵量和机身姿态角,从而计算直升机需用功率。通过研究直升机功率与旋翼半径、前飞速度、直升机起飞重量以及飞行高度之间的关系来确定直升机需用功率的降低幅度,同时也分析了旋翼桨距和机体倾斜角随旋翼半径和前飞速度的变化趋势。在中高速飞行时,特别是高速飞行时,旋翼半径的变化可以显著地提升直升机的性能。当飞行速度为200km/h、旋翼半径减小20%,需用功率可降低37.6%。随着飞行高度的不断增加,在低速到中速飞行时直升机功率减小幅度会减小,在高速时功率减小幅度会增大。旋翼总距和纵横向周期变距随旋翼半径减少而增加,机体纵横向倾斜角随半径减小而减小。     

Integration of high-fidelity model of forward variable area bypass injector into zero-dimensional variable cycle engine model

Forward Variable Area Bypass Injector (FVABI) is one of key components which contributes to modulate the cycle parameters of Variable Cycle Engine (VCE) under various operation conditions. The modeling method of zero-dimensional FVABI was reviewed and its deficiency was analyzed based on FVABI flow characteristic. In order to improve the accuracy of VCE performance simulation, the high-fidelity modeling method of FVABI was developed based on its working characteristics. Then it was coupled with the zero-dimensional VCE model and the multi-level VCE model was built. The results indicate that the geometric and aerodynamic parameters can affect the interaction between the two airflows and the zero-dimensional FVABI model is too simple to predict the component performance accurately, especially when the FVABI inner bypass is chocked. Based on the performance curves for single bypass mode and the regression model of multi-scale support vector regression for double bypass mode, the high-fidelity model can predict FVABI performance accurately and rapidly. The integration of high-fidelity FVABI model into zero-dimensional VCE model can be done by adjusting iterative variables and balance equations. The multi-level model has good convergence and it can predict VCE performance when the FVABI inner bypass is chocked.     

变循环发动机模态转换数值模拟

对双外涵变循环发动机的模态转换过程进行了研究,设计了变循环发动机模态转换方案,确立了模态转换时的多部件调节规律,采用稳态模型对模态转换进行了数值模拟.结果表明,所设计的模态转换方案可行,能够使变循环发动机的涵道比发生明显改变,并有效提高了发动机在部分推力时的空气流量,与设计参数相同的常规涡扇发动机相比,其安装耗油率明显降低.      

Experiment of drag characteristics of a novel variable geometry flame-holder

A novel variable geometry flame-holder (VGF) based on V-gutter was presented. The structural characteristics of the flame holder were introduced. Experimental study on drag characteristics of the VGF on un-burning and burning states was conducted in a rectangular combustion test rig. The influence of the change of gutter trailing edge width w on pressure recovery in different operating conditions was analyzed emphatically. Furthermore,drag characteristics in different trailing edge width variation modes were discussed. Results show that: (1) Narrowing w can observably raise the total pressure recovery σ but the highest σ is not obtained at minimum w. (2) The relationship of drag coefficient ψ and w in the un-burning conditions can be well expressed in a form of exponential equation (w/d>0.4). (3) Drag characteristics are not sensitive to the variation modes and speeds of w . (4) In the burning condition,σ decreases with the increasing of w basically and the course can be divided into three stages. The results and experimental data presented in this paper would enhance the phenomenological understanding of this type of VGF,and would contribute to the next experimental study and numerical calculus of this novel VGF.      

电控罗经的变传递系数阻尼方法

船用电控罗经在不同纬度下动态误差相差较大,为解决这个问题,提出了变传递系数阻尼方法。该方法解决了不同纬度误差变化大的问题,并在某电控罗经中得到成功应用。     

飞机钣金组件数字化装配误差分析

以飞机数字化制造装配为依托,通过对飞机钣金组件在模拟量协调路线和数字量协调路线下产生误差环节的比较,着重分析了飞机钣金组件在数字化装配过程中产生的系统误差和随机误差的因素和造成误差累积的原因。针对减小在钣金零件制造路线、钣金组件装配路线、温度场变化、振动场变化、应力变化等环节的累积误差提出了改进措施。     

基于优化的蜂窝板有限元模型修正

蜂窝板具有较高的比强度和比刚度,在航空航天领域得到广泛应用。用三明治等效方法计算蜂窝板等效材料参数,在MSC.Patran中建立有限元模型计算蜂窝板基频,通过分析设计变量和目标函数在NASTRAN中对蜂窝板基频进行优化,利用优化结果确定等效剪切弹性模量计算公式中修正系数γ并重新计算修正后模型基频,以试验所测基频值为标准对蜂窝板有限元模型进行修正。修正后模型计算基频值与实测值之间的偏差明显减小,证实了模型修正的有效性。     

宽马赫数范围高超声速进气道转动唇口变几何方案研究

结合简单一维流理论讨论了一种工作于Ma=4～7、采用可转动唇口的变几何二元高超声速进气道设计方案,并利用数值仿真手段对其Ma=4下的自起动性能及其他不同工作马赫数下的性能进行了研究.结果表明:所设计的变几何进气道必须辅以附面层排移措施才能在Ma=4下顺利实现自起动;该变几何方案Ma=4下的流量系数达0.7以上,这为飞行器加速提供了强有力保障;与定几何进气道相比,变几何进气道高低马赫数下的总体性能均得到显著提高;此外,转动唇口的铰接位置对自起动性能有重要影响.      

变比热对超燃冲压发动机尾喷管设计的影响分析

当气体总温较高时,气体的比热比将不再保持不变,而是温度的函数。由于超燃发动机尾喷管的入口温度很高,因此,在喷管型面设计时应该考虑比热变化对型面产生的影响。给出了基于量热完全气体模型和热完全气体模型的超燃冲压发动机尾喷管设计方法。并比较了比热比不变和比热比随气体温度变化时对喷管型面设计的影响。对量热完全气体的应用限制进行了初步讨论。     

充气机翼的褶皱与失效行为研究

在经典工程梁理论的基础上,结合张力薄膜的应力状态分析,提出充气机翼褶皱失稳的判据。计入表面薄膜褶皱引起的刚度退化效应,将机翼等效处理为一个变截面刚度的梁,建立了充气悬臂机翼的等效梁模型,并采用微分求积法进行充气机翼弯曲变形分析。计算结果与充气机翼的静力弯曲试验结果相吻合,验证了充气机翼弯曲变形分析方法的有效性。应用片条理论引入气动力模型,并与所建立的等效梁模型相耦合,建立充气机翼的静气动弹性耦合模型,并用迭代算法进行求解。考虑起皱和失稳两种判据,并计算获取了试验机翼的起皱动压和皱褶失稳动压形式,计算结果与风洞试验结果一致。根据所建立的充气机翼静气动弹性分析方法,可以预测充气机翼表面褶皱区的扩展和弯曲变形,进而绘制充气机翼的静气弹许用包线,为充气机翼的设计提供必要的安全边界参考依据。